
i.MX8 Boot process and creating a bootable image
Jan 19, 2024 · sudo dd if=iMX8QX/flash.bin of=/dev/mmcblkX bs=1k seek=32 If the desired target is a QM variant change if=iMX8QX... to if=iMX8QM. Then match your SD card device on "of=/dev/mmcblkX" you can see how your SD card enumerates by typing lsblk on your console before and after inserting your SD card.
How to flash uboot binary on iMX8MQ eMMC using dd …
Mar 31, 2021 · I was able to flash the imx8mq uboot binary with uuu but I need to know the equivalent dd command to flash uboot binary to emmc. I successfully flashed uboot environment on emmc with the following command. dd if=u-boot.env of=/dev/mmcblk0 bs=1k seek=4096 conv=fsync (the offset is same as sd-card)
Manually build Boot binary for i.MX8M Mini - NXP Community
Feb 5, 2020 · Sometimes it is helpful/faster to build a i.MX8MM boot binary outside of the Yocto environment. There are instructions on how to accomplish this on different places, this document tries to provide an example for the i.MX8M Mini LPDDR4 EVK, whenever possible pointing how to build for other boards.
Updating U-Boot with an A/B Strategy - Burkhard Stubert
May 13, 2024 · The package imx-boot adds some iMX-specific features to u-boot. The package mmc-utils provides the utility mmc to switch between the two boot paritions or to find out the current u-boot version or the current boot partition.
i.MX8 - iMX8MEVK - Yocto - Installing an Image - RidgeRun …
Nov 5, 2024 · In old Yocto versions (before Sumo) the most common image type was sdcard, use dd with this image type. IMAGE=fsl-image-multimedia-full-imx8mqevk-20181018224131.rootfs.sdcard DEVICE=/dev/sdb # The device may change in your system sudo dd if=$IMAGE of=$DEVICE bs=4M && sync
The imx-boot binary includes the Uboot, ARM trusted firmware, DCD file (8QuadMax/8QuadXPlus), system controller firmware (8QuadMax/8QuadXPlus), SPL(8MQuad), DDR firmware (8MQuad), and HDMI firmware (8MQuad).
To begin partitioning the storage space on the board, the necessary files must be obtained. There are two main methods of getting a deployable image as explained below: The first method involves downloading the Linux BSP pre-built binaries, which offer a starting point for testing the features supported on the evaluation boards.
$ sudo dd if=<zImageName> of=/dev/sd<partition> bs=512 seek=2048 conv=fsync && sync To flash the device trees generated from the build, execute the following commands: $ sudo dd if=<DevicetreeName>.dtb of=/dev/sd<partition> bs=512 seek=20480 conv=fsync NOTE For i.MX 8QuadMax and i.MX 8QuadXPlus, the kernel image
Yocto build and SD card flashing guideline for iMX8M Plus - NXP …
Feb 16, 2024 · For the distro we have used fsl-imx-xwayland. Once the build is done, we have used a 16 GB SD Card and flashed the wic using the following command: zstdcat .wic.zst | sudo dd of=/dev/sd bs=1M conv=fsync.
Booting a single image on different mx6sabresd boards
Oct 5, 2017 · In each case a u-boot.imx binary is generated and can be directly flashed into the SD card: sudo dd if=u-boot.imx of=/dev/mmcblk0 bs=1K seek=1; sync With this method one different binary is needed for each of the mx6sabresd board variant.
- Some results have been removed